Apri APP!

Godetevi le offerte esclusive.

Apri APP
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1
1/1

Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1 - Blu

13.89€
22.99
9 Recensioni

Coupon:

Promozione:

Supporto pagamento COD

Magazzino e costo

Selezionare
P-1000:Spedisce tra: Oct 30 - Nov 06

Opzioni del prodotto

Selezionare
Blu
Visita il negozio

Recensioni (9)

Barney
Jul 11,2019
Great shipping. Works well with drv8825 setpper drivers. Upgraded my Tronxy with a melzi board to the mks gen l with DRV8825 stepper drivers. im impressed so far. does not have an sd card but it comes with the 12864 raprap screen. the original tronxy lcd 2004 does work ons aux3 connection with one down side that you will have to change the 5v and ground on the 10pin cable this is pin 1 and 2 needs to be swapped to get the 2004 lcd working.
Vedi di più

Descrizione

Caratteristiche principali

Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS Gen_L, which provides more flexible choices for users.


1. 2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors.

2. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change the stepper drivers and motors as users like.

3. Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors.

4. Use high-quality MOSFET, better cooling and more stable.

5. Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage.

6. Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing.

7. Use CH340 serial port chip, more easily install the drive than 16U2.

8. Run firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4.

9. Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32.

10. Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats.

11. X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire.

12. Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage.

PIN port map

specifiche

Dimensione del pacchetto (L x W x H)
15 * 10.5 * 4cm
Pesi del pacchetto
130g
Contenuto dell'imballaggio
Scheda madre MKS Gen L V1.0 * 1 Linea dati USB * 1
Vedi di più

Prodotti consigliati

Prodotti sponsorizzati

Bonus per i nuovi membri: buono da $50
13.89€

Controller della scheda madre della scheda di controllo della stampante 3D HESAI MKS Gen L V1

Colore

Blu
Quantità - +
Rate: Scegli
loading...
loading...
Annulla
loading...
loading...
loading...

Recensioni

5 *****
  • 9
  • 0
  • 0
  • 0
  • 0
  • Tutti ( 9 )
  • ( 2 )
  • ( 0 )
Barney
Jul 11,2019
Great shipping. Works well with drv8825 setpper drivers. Upgraded my Tronxy with a melzi board to the mks gen l with DRV8825 stepper drivers. im impressed so far. does not have an sd card but it comes with the 12864 raprap screen. the original tronxy lcd 2004 does work ons aux3 connection with one down side that you will have to change the 5v and ground on the 10pin cable this is pin 1 and 2 needs to be swapped to get the 2004 lcd working.
Jasse Salonen
Aug 05,2019
Very rarely happens when i write a review. But this seller surprised me. This is a sample of the quality of the packaging, the level of communication and the speed of delivery from china to the kaliningrad region. I do not recommend, but strongly advise buying here if you appreciate the time.
Kyle Sagarsee
Aug 05,2019
The order was delivered very quickly, a little less than two weeks, the controllers need to buy, the duck is whole, the quality of the soldering is excellent, the flux is washed. I recommend this seller.
Kaio
Aug 01,2019
Instead of gen l v1.0 sent mks base v1.4, some money returned, but other drivers no longer put. Works. Product description product came in 10 days product and seller recommend
Frederica Crichton
Jun 25,2019
Solid board, soldered points look fantastic, the board is laid out well.All in all, especially for the price, I'd highly recommend this if you're wanting to upgrade your stuff.
Rodolphe RIU
Aug 06,2019
The board is received, everything is fine, from the first start you need to put the firmware and calibrate the sensor. Everything works, seller thanks! 5 stars to you)
Bernard Milton
Jun 24,2019
I just finished installing, the build quality is excellent, and it can change the stepper drivers and motors as my needs.
Nicole Berkeley
Jun 26,2019
Firmware loaded easily and ran the machine with no modifications.Don't wire it wrong and you will be fine.
User
Sep 27,2019
Sehr gut verpackt und schnelle Lieferung. Marlin eingespielt und es läuft alles Tip Top.Werde noch 2 Bestellen für die anderen Drucker.
Non ci sono più commenti
Vedi di più
Vedi di più